These motors are used in 4Borg and have a good deal of torque thanks to the high gearing.
Approx 17mA draw at 6V free running, approx 50mA under load.
With 22awg solid core wire soldered on to the terminals (approx 5.5" cable length)
Brass Hub with 7mm shaft hole for connection to 7mm motor shaft.
Includes two grub screws and one M4 screw for securing to wheel.
(Fits our wheels and most 1/10 scale RC wheels) Download hub size and dimensions PDF
Please note hub sizes for our products:
Brass Hub with 6mm shaft hole for connection to 6mm motor shaft.
Includes two grub screws and one M4 screw for securing to wheel.
(Fits our wheels and most 1/10 scale RC wheels) Download hub size and dimensions PDF
Please note hub sizes for our products:
Brass Hub with 5mm shaft hole for connection to 5mm motor shaft.
Includes two grub screws and one M4 screw for securing to wheel.
(Fits our wheels and most 1/10 scale RC wheels) Download hub size and dimensions PDF
Please note hub sizes for our products:
Brass Hub with 4mm shaft hole for connection to 4mm motor shaft.
Includes two grub screws and one M4 screw for securing to wheel.
(Fits our wheels and most 1/10 scale RC wheels) Download hub size and dimensions PDF
Please note hub sizes for our products:
Brass Hub with 3mm shaft hole for connection to 3mm motor shaft.
Includes two grub screws and one M4 screw for securing to wheel.
(Fits our wheels and most 1/10 scale RC wheels) Download hub size and dimensions PDF
Please note hub sizes for our products:
These motors provide DiddyBorg Metal Edition and Red Edition with their torque and speed, allowing them to climb inclines quickly.
Quality 12V 100RPM metal gear motor with mount, hub and wheel.
Also includes allen key, M4 screw, 2x M3x8 screws and 2x grub screws.
Single motor, Six of these are required for DiddyBorg Metal Edition or Red Edition.
Mounting kit for the HC-SR04 module. Includes stainless steel mount, a 4 pin cable, 4 screws and 4 nuts. Shipped flat, it can easily be bent to 90 degrees. Repeated bending can cause metal fatigue. To avoid the risk of sharp broken metal, please only bend once. HC-SR04 module sold seperately.
Hi torque servo motor with 10Kg.cm stall torque! Standard 3 pin servo connector requires 5V, GND and PWM signal.
A range of servo horns and mounting screws are included.
Metal gears
Specifications
Stall torque @4.8V
9.4 Kg.cm
Stall torque @6V
12Kg.cm
Rotation max
120 degrees
Supply voltage
4.8 to 7.2V
Supply current @6V
0.9A
At widest point excluding cable and horn
Approx 54mm x 19mm x 45mm
Approx 57g
These motors provide DiddyBorg with it torque and speed, allowing them to climb steep inclines.
Quality 6V 60RPM metal gear motor with mount, hub and wheel.
Also includes allen key, M4 screw, 2x M3x8 screws and 2x grub screws.
Single motor, Six of these are required for DiddyBorg.
Clear Raspberry Pi case for a Model B Raspberry Pi. Works with Rev1 or Rev2 modelB. Includes screws for Rev2 model B.
Raspberry Pi, SD card and cables not included!
5V DC TTL level ultrasonic distance sensor. Provides approximate 2cm to 4meter range. VCC, trig, echo and GND connections. We also have a Stainless steel HC-SR04 mounting kit available seperately
Quality 9V connector cable for use with 9V battery or AA battery holders with eyelet connectors (such as our 2,4,6,8 and 10xAA holders).
Thick 22AWG 1061 UL/CSA approved wires for low resistance connections and less likelyhood of breakage. 6.5" in cable length.
Battery holder for 6x AA batteries, with 9V style connector.
Comes with matching 9V connector with wires.
Should provide a 7.2V output with rechargeable batteries.
Not recommended for use with BattBorg if using rechargeable batteries.
Batteries not included.
Battery holder for 2x AA batteries, with 9V style connector.
Comes with matching 9V connector with wires.
Suitable for powering 3V motors with PicoBorg.
Not suitable for BattBorg.
Battery holder for 10x AA batteries, with 9V style connector.
Comes with matching 9V connector with wires.
With 10x AA batteries, BattBorg should run for approximately 25% longer than 8x AAs.
Batteries not included.
Battery holder for 8x AA batteries, with 9V style connector. Comes with matching 9V connector with wires.
Great for use with BattBorg. In our tests a set of 8x 2700mAh rechargeable AAs lasted for approximately 14h 30m using BattBorg.
Batteries not included.
Soldering iron suitable for assembling BattBorg kits, PicoBorgs, motors, and other electronics.
BS approved with a UK standard 13A plug. 230V CE marked.
Please read the included safety instructions.
Please note delivery available only to UK.
2 meters of lead free solder, perfect for assembling kits.
97.1% Tin, 2.6% Silver, 0.3% copper. Added to 2.2% flux (intended to be no clean) and drawn out to 0.5mm diameter.
Has a lower melting temperature (217 deg C) than most lead free solder (~227 deg C)
Please ensure adequate ventilation and safety whilst soldering.
USB Bluetooth module for your Raspberry Pi.
Adds the ability to connect Bluetooth devices to your Raspberry Pi, such as keyboards, joysticks, and game controllers.
Perfect for controlling media centres, robots such as PiCy, and other remote applications.
If you have a PS3 controller see the Raspbians PS3 Bluetooth guide here to use it with this Bluetooth module.
Powered from the Raspberry Pi.
USB WiFi module for your Raspberry Pi.
Adds the ability to connect to wireless networks, allowing you to talk to your Raspberry Pi remotely.
Perfect for controlling robots such as PiCy and other remote applications.
Powered from the Raspberry Pi.
Battery holder for 4x AA batteries, with 9V style connector.
Comes with matching 9V connector with wires.
With non-rechargeable batteries the holder should provide 6V, suitable for many 5V regulators to power 5V devices such as a Raspberry Pi.
Not suitable for use with BattBorg.
One DC motor and wheel, for use with picoBorg.
Can be used to make roving Robots from the Raspberry Pi.
15rpm output shaft gearbox means powerful enough to tackle inclines and carpet at around 3 meters/min
3V motor, 160mA so can be run from 2xAA batteries.
Approx 65mm diameter wheel inc. tyre, 25mm wide tyre, width including motor approx 50mm, length including motor and wheel approx 90mm